Inflatable 2/3 person touring Kayak High-pressure Bottom - X100+

INFLATED SIZELength: 410 cmWidth: 102 cmFOLDED & BAGGED SIZEHeight: 72 cmWidth: 45 cmThickness: 37 cmWeight: 18 kgMaximum floor pressure: 0.34 bar (5 psi)Side tube and seat pressure: 0.2 bar (3 psi)Number of seats: 2 or 3 seatsContent: kayak, bag, repair kit, 3 fins, user guide, inflation connector, strap.PUMP NOT INCLUDEDFor use with an Itiwit double-action hand pump with adapters

Connect the ITIWIT pump (sold separately) by twisting the pump adapter 1/4 turn and inflate the floor to 5 psi. Finish by screwing the cap back on.Put the floor inside the kayak and strap it at the ends. The floor valve must be aligned with the side tube valves located at the back of the kayak. The floor's position must allow free access to the drain plugs located in the middle of the kayak.

Connect the ITIWIT pump (sold separately) by twisting the pump adapter 1/4 turn and inflate the side tubes to 3 psi. Finish by screwing the cap back on.Each side tube has a pressure relief valve. Its purpose is to evacuate excess air resulting from overinflation. When this happens, you may notice a hissing sound. This hissing is normal, it can happen during inflation or after prolonged exposure to sun. It will stop once the kayak reachesthe correct internal pressure

The seats are high, providing increased comfort for adults in the paddling position.Position the seats on the floor using the rip-tab areas located under the seat and on the floor.Stow any bags or equipment into the kayak's rear hatch or attach to the rear deck.The boat is ready to be launched.

The deck of the Itiwit 100+ is based on the same dropstitch construction as the inflatable stand-up paddle boards. Dropstitch is a mesh made of polyester yarns between two layers of PVC. When the deck is inflated to a high pressure, the threads are stretched and the construction becomes very strong, thus avoiding any deformation.

Remove the seats and slightly deflate the floor to make it easier to rinse out.Rinse the kayak, floor and seats with clean water after each use to avoid damage from sand, salt water and sun.Open the drain plugs located in the middle of the kayak and at the rear. Tip the kayak to empty out the water.

Make sure that the surface you intend to fold the kayak on is clean. Remove the fins.Deflate the side bladders. The valves are located at the back of the kayak. PLEASE NOTE: Do not unscrew the pressure relief valves at the front.Fold the floor.Fold the rest of the kayak in half lengthwise. Flatten the front fin base.Lay the rolled floor on the front end. Roll the kayak to the rear end.Strap the kayak.

Once dry and clean, the kayak should be stored in a dry and shady place, protected from significant temperature changes.The kayak can be stored folded but if you have enough space, storing it flat and slightly inflated will extend its life.

Spare parts are available for Itiwit X100+ kayaks from after-sales service. Visit the workshop at your nearest Decathlon store to collect or order some.Drop Stitch floor: 8561072Pressure relief valve: 8561069Carry bag: 8605095Paddle rip-tab: 8561070

We recommend that you use the product with a buoyancy vest.

Is your canoe-kayak inflatable or rigid and is less than 3.50 metres? You have what is called a beach craft.You must always stay within 300 metres of a shelter (any place on the coast where any craft or vessel and its crew can get to safety by anchoring or berthing, and set off again without assistance).Buoyancy life vests are not mandatory but strongly recommended to make it easier to get back in the boat if you fall out.

Your canoe/kayak is rigid or inflatable with at least 2 separate air chambers. It measures more than 3.50 metres. It is approved for sea use by the manufacturer.You can paddle up to 2 nautical miles (approx. 3 km) from shore. You must carry a number of items of safety equipment.You can find a list of these items via this link: https://www.itiwit.fr/reglementation-pour-faire-du-canoe-kayak